Other Products ｜Chem-Rock LV

Chem-Rock LV

Available Sizes

1.5 Gallon BAG-PAKTM Unit in a single pail
3 Gallon BAG-PAKTM Unit in a single pail
15 Gallon Unit in three 5-gallon pails

Advantages

100% solids
Faster cure available using CHEM-ROCK ACCLERATOR
Excellent inter-coat adhesion to ROCK-TRED primers and finish coats
Self-leveling, easy flowing product
Odorless / VOC compliant
Water-clear, high gloss finish
Easy mix ratio
Good UV and chemical resistance
Useful as a water clear 100% solids epoxy primer

Description
CHEM-ROCK is a water clear, 100% solids, 2-component, cyclo-aliphatic, low viscosity epoxy coating. CHEM-ROCK LV is a multi-use coating designed to provide very good abrasion and chemical resistance, UV protection, gloss retention, durability and workability for the applicator.
Uses
CHEM-ROCK LV low viscosity epoxy is used where a water clear or solid color thin mil "neat" coating is required or when a highly flowable, self-leveling finish coat is required. Its low viscosity characteristic allows easy application and uniform application in thin, tight coats. CHEMROCK LV is VOC compliant and meets all USDA/FDA guidelines for use in federally inspected facilities.
Typical Coverage
CHEM-ROCK LV is typically applied between 100-160 square feet per gallon per coat depending upon substrate and project requirements.
Physical Properties

Volume mix ratio
2 to 1 (Resin to Hardener)

Viscosity (mixed)
600-700 CPS Typica

Solids Content (%)
100% (ASTM D-2697)

Hardness (ASTM D-2240)
75-85 (Shore D)

VOC
Compliant with all US Regulations

Application Temps.
60° – 85° F

Gel Time
30-40 minutes @ 75° F

Dry to Touch (recoat with compatible products)
2-3 hours @ 75° F

Through Cure
7-9 hours @ 75° F

Open for light traffic
24 hours @ 75° F

Shelf Life
1 Year in unopened units

Limitations & For Best Results

Do not thin this product.
Do not apply when Humidity exceeds 70% indoors.
Do not allow to puddle during application.
Allow each coat to dry to 'tack-free' or clear prior to re-coat.

When re-coating, always apply the next coat within 24 hours of completing the previous coat.
Do not apply less than 10 mils per coat as separation may result.
When pigmenting this product using lighter colors two 10-12 mil coats may be required for full hide.

Product Application
Apply using brush, roller and squeegee ROCK-TRED product test data is based on environmental temperatures of 75° F (24° C). Viscosity and working time are always affected by temperatures above or below that mark. When applying product always consider the ambient, surface, and product temperature at the time and place of installation.
Color and Textures
CHEM-ROCK MV is manufactured in WATER CLEAR and can be field pigmented using ROCK-TRED colorants. Most ROCK-TRED products are available in a wide range of textures using an appropriate aggregate.
Chemical Resistance
Always refer to ROCK-TRED's chemical resistance chart for specific information on each product / system or contact ROCK-TRED directly.
Product Storage
DO NOT allow ROCK-TRED products to freeze. All ROCK-TRED products should be properly stored above the floor on pallets or shelves, and in an area that has a constant minimum temperature of 50°F.
Surface Preparation
Always apply ROCK-TRED products to a clean / sound substrate that is free of laitance, grease, oils, debris, and curing compounds. Concrete substrates should be cured for a minimum of 28 days prior to application of product [except as otherwise noted on the individual Product Data Sheet]. Whenever possible, remove existing coatings and/or flooring systems completely; if complete removal is not possible always perform tests to determine adhesion and compatibility to the existing flooring. Mechanical preparation by means of a shotblasting or diamond grinding machine to a minimum CSP-2 profile followed by application of an appropriate ROCK-TRED primer or base system is the best and recommended installation method for CHEM-ROCK LV applications. If the substrate is not properly prepared and the appropriate profile is not achieved, failure of the product to adhere to the substrate may occur.
Clean Up
Application tools and equipment can be cleaned with soap and water immediately after use, or with solvent once the product has begun to cure.
Disposal
Product containers will contain product residue and must be disposed of properly. Label warnings must be observed at all times. All containers must be disposed in accordance with federal, state, and local regulations.
Important Notice
Always read and acquaint yourself with ROCK-TRED's Product Data Sheet, SDS [safety data sheet], and product labels for each individual product prior to mixing and prior to use. For further assistance, product questions, additional information and/or unexpected or unusual installation conditions – contact your Area Sales Representative or ROCK-TRED directly for recommendations. Kit components are pre-measured for optimal performance. Catalyzation errors due to incorrect mixing in the field voids product warranty.
Brand:Rock TredSKU:16802BPTags:Clear Epoxy, Rock TredSize:1.5 Gallons, 3 Gallons, 15 Gallons